W9GSV
Liam Bennett
grid
DN86
qth
ND
time
--:--:--Z

End-fed Half Waves

The modern End-fed Half Wave (EFHW) antenna is affordable, practical and deservedly popular. The EFHW is a commonly recommended first antenna for new hams to toss up if they want to explore multiple HF bands with one wire. A single wire is easy to hide in suburban environments and the EFHW lends itself well to compromised installs. For POTA and SOTA, EFHWs can be made compact and lightweight, and are easy to deploy in a tree.

Theory

An end-fed half wave is a dipole. A dipole can be fed anywhere along its length, provided the feedpoint impedance is properly matched to the transmission line. A conventional dipole is typically monoband and center-fed at the current maximum. See the plot below for the idealized current and voltage distribution along a ½λ dipole. Dipole current and voltage distribution plot

However, a center-fed dipole can be used on its fundamental frequency and also its odd harmonics, as the odd harmonics also have a current maxima in the center of the antenna. This trick is commonly used for 7/21 MHz dual-band operation with a single dipole (although I’ve never had any luck with it). Below, I have added 21 MHz to the plot of voltage and current distribution. Both frequencies resonate on a ~21m long dipole, and both have a current maximum in the middle of the wire. Note that due to relative elevation over ground (in wavelengths) for each frequency and wire end effects, the real feedpoint impedance for the fundamental and the harmonics will not be the same.

Dipole current and voltage distribution plot

In the plot above, both 7MHz and 21MHz also had a voltage maximum at the start of the wire. This is true for all harmonics of the fundamental. Conveniently, the ham bands are harmonically related. See plot below for the voltage and current distribution of 14 MHz on a 21m long wire (a full wave dipole). Note that it also has a voltage maximum at the beginning of the wire.

Dipole current voltage distribution plot

EFHWs are rarely just one wire. Typically, a short counterpoise ~0.05λ long on the fundamental, provides a high impedance return path, and helps keep RF off the feedline with proper choking.

On the fundamental frequency, the EFHW has the same far-field radiation pattern as any dipole, with slightly lower gain due to losses in the unun. However, on the higher harmonics, multi-lobed "figure-8" patterns start to appear.

Part of the allure of EFHWs is that they are resonant on multiple bands. I prefer resonant antennas in almost all cases. While there are good reasons to eliminate a transmatch by using a resonant antenna, I’m not sure my preference comes from a deep technical analysis of the trade-offs. They’re simply what I like.

Construction and Installation

For most of the EFHW’s modern period of prominence, it has been inseparable from the FT-240-43 ferrite toroid. Recently, excellent work has been done by hams, notably MM0OPX, popularizing the Fair-Rite 2643251002 as an alternative. The Fair-Rite 2643251002 has a similar mass of ferrite to the FT-240-43, but is a smaller diameter with a higher cross-sectional area. This allows the unun to be more efficient and have lower insertion losses. My current 49:1 impedance transformer uses the Fair-Rite 2643251002, wound as an autotransformer with 18 AWG wire, with a 2 kV 150 pF capacitor across the input.

An EFHW can be installed horizontally, as an inverted vee, vertically, or as a sloper. For better DX performance, install it vertically, or horizontally at ½λ above ground to maximize low-angle radiation. For omnidirectional, multipurpose use, an inverted vee with the apex elevated to ½λ of the fundamental is a good place to start. A horizontal installation 6–10 ft off the ground makes an effective NVIS antenna. A 40m EFHW can also be configured as a 20m half-square antenna, giving excellent low-angle gain on 20m while retaining NVIS properties on 40m. This is a configuration I hope to explore.

I have now built and installed three end-fed half-wave antennas: a 135’ copperweld 80m monster with a homebrew 49:1 unun using an FT-240-43, essentially following the ARRL kit design; a QRP unun kit with a mini no-tune QRP Guys and a 33’ wire; and the 66’ low sloper I currently use at my North Dakota QTH.

Notes:

  1. It is impossible for an EFHW with the feedpoint on the ground to ever be high enough (horizontally) for optimal low-angle performance.
  2. Expensive commercial 49:1 match units may be more suitable for QRO, but building transformers is straightforward and much cheaper than buying. Try it!
  3. All of my best DX has been with resonant verticals, not EFHWs. My quietest antenna was a high 20m center-fed dipole, and I miss it.
  4. RF in the shack does tend to show up. I’ve gotten much more disciplined about choking now, but I have not had these issues with other antennas. A 1:1 current choke should be used at both the radio and antenna feedpoint (or 0.05λ from the antenna feedpoint if not using a counterpoise).

Back to the Log